The mounting hardware will depend on what length shackle straps you need for the MORryde Shock Absorbing Suspension Equalizers for Tandem Axle Trailers w/ 35" Wheelbase - 8K # MR27ZR.
You can use either the MORryde Suspension Upgrade Kit for Tandem Axle Trailers - 2-1/4" Long Shackle Straps # MR46ZR or 3-1/8" Long Shackle Straps # MR76ZR. view full answer...
If your current remote looks like the Replacement New-Style Linc Analog Remote # LC292614 then yes this would be the correct replacement for it. If it doesn't we do not have a solution. view full answer...
The AC490TT-B part number you got from Keystone is for a center cap with a 4.9" pilot hole diameter. The Lionshead Trailer Wheel Center Cap w/ Snap-In Plug item # LHCS109-SI60C will fit. This center cap fits 8-lug wheels with a 4.88" to 4.9" pilot diameter. view full answer...
The 7,000 lb double-eye leaf spring we have that is closest to 26" is the 24-7/8" long 6-Leaf Double-Eye Spring for 7,000-lb Trailer Axles # e64SR.
Assuming yours have flattened a good amount (which will definitely be true if the trailer is older), these will work out as a good replacement. You mentioned hardware, and I'm assuming you were referring to U-bolts, shackle bolts and straps. You'll need to measure your shackle straps but you can use the following:
- U-Bolt Kit # APUBR-9
-... view full answer...
The part number 297697 is for a Dexter 7K axle.
There is a full bearing kit for this. It's part # BK3-200. It includes the bearings, races, and seals.
Of course, this is not a definite replacement as I could not find exact numbers for your axles. It's very likely that this is the right one, but you should still check the numbers of your current bearings, races, and seals to ensure they match this one's:
Inner bearing: 25580
Inner race: 25520
Outer bearing: 14125A
Outer race: 14276
Seal:... view full answer...
Yes, The Landing Gear Set w/ Handle # RVLG-8HDL will work with your 2010 Keystone Montana Hickory Fifth Wheel.
The landing gear has a durable, black powder coated outer tubes that has a zinc-finished inner tube that provides excellent corrosion resistance. It has a weight capacity of 8,000 pounds. The 12V DC Motor # LC142178 is sold separately.
I attached a review video link below. view full answer...
The Replacement Gearbox for Venture Aluminum Electric 5th Wheel RV Landing Gear Assemblies # LC276602 is the correct replacement for your Venture landing gear. view full answer...
I went ahead and consulted the owner's manual for your Furrion RV Tankless Water Heater - Gas - Automatic Pilot # FR68SR, and this symptom is correlating with there could be lime scale forming due to precipitation of hard water.
To fix this, Furrion recommends that you decalcify your water heater. You're also going to want to ensure that your water heater is producing the minimum water flow of 0.32 gallons per minute.
If it's not, what you can try and do is if your unit is equipped with... view full answer...
The best option to lift your 2011 Keystone Montana 3100RL is not technically a lift kit, but what is called an over/under conversion kit, which is sometimes referred to as "flipping the axles." This kit going to give you the most clearance, raising your trailer approximately the same amount as your axle's diameter plus the height of the leaf spring pack (please keep in mind this conversion kit is for use with double-eye springs only).
Your 2011 Montana 3100 RL should have tandem 3" round... view full answer...
Lippert was unable to identify exactly what you have based on part numbers, but I can still help you find the correct replacement. You will need to check and see where the landing gear is mounted and also measure the black outer tube on your existing leg. If the landing gear is mounted on the inside of the frame rail you need one of the following:
-Replacement Follow Leg for Venture 5th Wheel RV Landing Gear # LC119101 (29-1/2" Measurement)
-Replacement Follow Leg for Venture 5th Wheel... view full answer...
We haven't fit the SolidStep Manual Fold-Down Steps, # LC791573 specifically to a 2010 Montana. However, if you let me know the dimensions of the well step, how wide your door frame is and how high your threshold sits off of the ground, I can help you find the correct SolidStep for your application.
Measure between the door frame flanges for threshold width, and measure from the mounting point to the ground for the entry height. view full answer...
It sounds like you may have an issue with the Receiver # LC305117 for the Linc Analog Remote # LC292614. Be sure to check the fuses in the receiver as well as the antenna wire for any damage. If you are not getting a click on the receiver after holding the momentary button on the receiver and the light button on the remote, Lippert recommended taking the batteries out of the Linc remote to let it normalize itself. view full answer...
For your 2013 Keystone Montana Hickory 3100RL the best option for a hitch that has a 500 lb tongue weight capacity is the Curt Multi Fit Hitch part # C13704 which fits standard RV frame styles that are between 22 and 66 inches measured from outside to outside. view full answer...
I spoke to a contact at Progressive Dynamics, he confirmed the Progressive Dynamics RV Power Control Center with AC/DC Panel and Converter/Smart Charger - 90 Amp # PD4590K18LS8 as a replacement for your 2011 Keystone Montana Hickory Fifth Wheel. view full answer...
Your 2010 Keystone Montana uses specific landing gear that is special to the Montana. The Lead Leg # LC178653 and Follow Leg # LC178652 are the ones you are needing.
If you find that either the Gearbox # LG-179015 or Motor # LC142178 are bad as well we do have the replacements for them as well. view full answer...
That's a great question.
The jacks sit in the 5th wheel frame mounted clips so that the tab on the upper end of the jack leg sits under the clip, and the tab on the lower end sits above the clip, as shown in the diagram on the right-hand side of the photo I provided.
The Lippert # LC178653 replacement lead leg has three tabs on it, and the spacing of the tabs is also shown in the photo. view full answer...
When it comes to adding a landing gear set to your 2010 Keystone Montana Hickory The Landing Gear Set w/ Handle # RVLG-8HDL will work for you.
The landing gears have a durable, black powder coated outer tube and has zinc-finished inner tubes that provide excellent corrosion resistance. The kit comes with a manual crank but you can purchase the 12V DC motor # LC142178 separately. The landing gear kit has a combined weight capacity of 8,000 pounds.
The lead leg of your landing gear is... view full answer...
Having Item # FVU1500WH on your vent is a great idea and I always recommend it when I do install videos on vents. You have also just pointed something out that I need to start making everyone aware of when I do the install videos so I thank you for that. The auto open and close feature on the vent actually doesn't have a limit whether it is opening or closing and you probably didn't notice it. The motor actually runs a few extra seconds after reaching the limit and then amps out. With a... view full answer...
The folks at SuperSprings tell me that ideally, you'd see about 1/4 inch of pre-load between the # TSS-107-40 spring and the underside of the trailer frame, but they tell even if there's no preload, the SumoSprings would still provide benefit. You can even trim the spring if you need to, but SumoSprings cautions that doing so will void the warranty. view full answer...